Below is a guide that will show you how to get stained concrete for your house. Remember that when you are applying acid stains to your concrete blemishes, impressions, glue, staining, or crack in the concrete will be visible. These stains create color effects that are translucent and will show surface defects that are similar to the application of stains to pieces of wood, stains highlight knots and any grains in the wood. After cleaning the concrete, completed surface training and preparation of the area, you may now start staining your concrete.
In case you have never carried this out and you are learning how to get stained concrete, the thing to remember is that you will be working with acid that has low strength. It does not have a lot of hazards, but it is crucial to protect yourself. Put on safety goggles and mask, cover your legs and arms, wear boots and gloves. The clothes you put on may get ruined with an overspray. The application of acid staining is the easiest fragment of the task. With that said, there exists a technique of doing it in the right manner. The very little stain will not give you full coverage and will not etch the surface well to deposit the color.
A lot of stained concrete will result in overreacting and puddling areas where stains have pooled. On big jobs, using accident resistant sprayers will work well, while you can use sponge brushes for small jobs (pool deck resurfacing tampa). Mix your stain according to the specs of the manufacturer on the bucket. Fill your sprayer and spray your concrete with an even coat of the stain. It is good to have an individual to follow you behind and scrub stains in your surface. Utilize the right approach, starting from the back and work to the area you may get from the floor with ease.
The broom will leave your stained concrete with strokes of the brush, therefore, after getting part of the job done, you will have to go back and mist more stained lightly on the brushed area. This will eliminate trailing brush strokes and provide you a consistent and natural look. You will have to start with one room side and work to the other side while keeping wet edges. Spray the path four feet wide in a back and forth manner until when the room is done. Allow the area to dry after finishing.
Time will also vary depending on the stain acid. Check for directions on buckets to get the approximate idea. Immediately the stain dries, you will have to neutralize your mixture with water and baking soda. This will stop reactions between the concrete and acid stain. You just need to mop and clean the residue with clean water, the wet vac, and the mop. Do not step on an area that has not been neutralized as this would leave footprints on your floor.
Clean your floor more than twice with a vacuum, water, and water only and allow it to dry. You will realize that after drying, the floor will look chalky or hazy. It will look good after sealing it. Once you are done for the day, you need to allow it to dry through the night. You can apply your concrete sealer the next morning. Since you know the techniques of getting stained concrete floors, you can now apply your sealer. When done in the right manner, it needs to be easy to apply. It is vital to utilize a sealer that will work well with your concrete stain. You may choose to spray it on or roll it on; taking care not leaves marks of the roller or spraying too much. A light coat will work best since you will have to apply another coat the next day.
After the application of the sealer, you will realize that the color of your stained concrete will start coming live. Your concrete floors will be looking beautiful and your hard work will be paying off. After the drying of the final sealer coat, you can move the furniture back to the house and start using the room once more. In case you require additional protection for the new floor and make it easy to clean, apply four coats of that floor wax.
Floor wax will add an additional protection layer to the acid stained concrete floors while making it look great and allow for easy cleaning. The finish of the floor applies with ease, you just need to pour it on the floor and then spread it with the applicator. Allow each coat to dry for one hour before applying the second one. Now that you understand staining the floor, you should be having the required confidence of tackling the plain gray floor and turn it into a gorgeous and unique thing. You can also get to http://www.customconcretetampa.com/ to get expert advice on staining your concrete.
Here is a list of our services you can get at Tampa’s Best Custom Concrete Pros & Concrete Repair Services:
10) Concrete Sinks
12) Custom Staining
14) Driveway Repairs
16) Metallic Epoxy
21) Sealed Concrete
22) Stained Concrete
24) Stamped Concrete
Request for a free quote from our Custom Concrete Pros & Concrete Repair Services Company now!
We also service all cities throughout Hillsborough County! Below are a list of cities where we offer our custom concrete repair services:
- Apollo Beach
- Plant City
- Temple Terrace
- Wesley Chapel
- All cities in the Hillsborough County area. Just call and ask!